Plumbing Basics: What You Need for Bathtub Installation
Plumbing Basics: What You Need for Bathtub Installation
Blog Article
We've discovered this article involving Tools You Need to Install a New Bathtub directly below on the internet and think it made perfect sense to relate it with you here.
Setting up a tub isn't specifically brain surgery, but it does need solid plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old bath tub with a brand-new one is likewise a reasonably challenging job. If the old tub is readily accessible, the project can move quickly; if you need to open a wall to eliminate the old bathtub and place the brand-new bathtub, the task is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will certainly need a helper to leave the old tub and also embeded in the brand-new one. Ensure you have certified yourself for the work and also fit attempting it. As opposed to hiring a specialist to take over a halfway-completed project, it is better to think about employing one before you begin. Possibilities are you may require a specialist plumber to make tube links.
This write-up will assist you mount a new bathtub in your washroom if you have already bought a brand-new tub and also don't need to transform the arrangement of your previous water supply pipelines.
Your tools and also material list ought to comprise the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The procedure of removing the existing taps can be quite problematic as a result of the restricted gain access to that is often the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly originate from the pipes. Once the supply pipelines have been gotten rid of, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the installing hole in the bath/basin guaranteeing that the washing machines are in area in between the tap as well as the sink. Safeguard the faucet in place with the producer supplied backnut. When the faucet is safely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap adapters. The previous type must be attached to the tap ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Using both wood boards under its feet, position the tub in the needed position. The wood boards are valuable in evenly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The next objective is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level and also readjusting the feet on the tub till the spirit level reviews level.
To set up taps, fit all-time low of the furthest flexible faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water supply and also examine all joints as well as new pipework for leaks as well as tighten them if necessary. Load the tub as well as additionally check the overflow electrical outlet and also the regular electrical outlet for leaks.
Finally, take care of the bathroom paneling as defined in the supplier's instruction manual. Tiling and also sealing around the bathtub must wait until the bathtub has been utilized a minimum of once as this will certainly settle it into its last position.
Getting ready for the Installation
First of all, the sustaining structure provided with the bathroom should be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets unit to avoid strain on the bathtub.
Fit the versatile faucet connectors to the bottom of both faucets making use of 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its last position.
Tiling Around the Tub
In the area where the bath meets the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to break an inflexible seal, creating the water to penetrate the wall in between the bath and the tiling, causing issues with wetness as well as possible leaks to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components and also fittings. They are offered in tubes as well as cartridges, and are capable of securing spaces up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked paper or soft rope. Remember to constantly fill up the bath tub with water before sealing, to allow for the movement experienced when the tub remains in usage. The sealant can fracture relatively very early if you do not take into consideration this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise conveniently readily available on the marketplace. It is advisable to fit the tiles making use of waterproof or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that piece of writing on Tools You Need to Install a New Bathtub while doing a lookup on the internet. Make sure you take a moment to promote this page if you enjoyed reading it. We treasure reading our article about How to Install a Bathtub Yourself.
Call Report this page